Offer
Provide additional details about the offer you're running.
FLASHSALE
Edmonton based
Industrial compressor service from an established local compressed-air company.
Kaeser Compressor Repair
Independent industrial compressor service in Edmonton
Kaeser compressor repair
Practical diagnostics, maintenance and repair support for Kaeser industrial compressors. Airtek works with current and earlier rotary screw, oil-free and MOBILAIR equipment across Edmonton and the surrounding service area.
Current and earlier equipment
Assessment begins with the exact model, serial number, controller and configuration.
Independent service
Airtek is not an authorized Kaeser service centre and does not represent the manufacturer.
Compressor and system diagnostics
A fault message is the starting point
Kaeser packages may combine the compressor, SIGMA controller, variable-speed drive, integrated dryer, condensate drains and other system components. A pressure complaint or shutdown can originate inside the package or elsewhere in the air system.
Airtek starts with operating history and the reported condition. We review the controller message, service hours, pressure and temperature behaviour, then determine a practical diagnostic path before recommending repair work.
Equipment families
Kaeser industrial equipment we can assess
Kaeser model names, controls and package options vary by generation and market. The families below help identify the equipment, but the nameplate and serial number determine the correct service information and parts path.
SX, SM, SK, AS and ASK
Belt-driven industrial screw compressors used in workshops and smaller production systems. Configurations may include a receiver, an integrated refrigerated dryer or SFC variable-speed control.
Also seen as AIRCENTER, AIRTOWER, T and SFC package variants.
ASD, BSD and CSD
Direct-drive rotary screw families for production and plant-air duty. Service assessment may involve the airend package, cooling circuit, inlet and separator system, drive motor, controller and optional dryer.
Fixed-speed, SFC and integrated-dryer configurations may be encountered.
DSD, ESD, FSD and HSD
Larger industrial compressor families used where plant demand and duty cycle require higher capacity. Work begins with operating data, site conditions and the machine's exact build information.
Air-cooled, water-cooled, fixed-speed and variable-speed versions exist.
CSG, DSG and FSG
Two-stage oil-free compressor families used where process-air quality is critical. Diagnosis must account for cooling, stage temperatures, controls and any integrated drying equipment.
Configurations may include T dryers, i.HOC drying or SFC variable-speed control.
MOBILAIR M-series
Towable, utility-mount and portable industrial compressors used for construction, municipal, service-truck, rental and field applications. Engine and compressor information are both important at intake.
Examples include M17, M27/M30, M55/M59, M58U, M76/M81/M82, M118/M125/M171, M255 and M480/M500 generations.
SIGMA and package systems
Earlier SIGMA CONTROL and current SIGMA CONTROL 2 equipment can store operating, maintenance and fault information. Integrated dryers, drains and downstream treatment also affect delivered-air performance.
Relevant names include SIGMA CONTROL, SIGMA CONTROL 2, SFC, SECOTEC, KRYOSEC and ECO-DRAIN.
This is not an exhaustive compatibility list. Earlier model generations and less common configurations are reviewed individually. Parts access and repair scope depend on the complete model and serial number, equipment condition and available technical information.
A faster first assessment
Send the machine details
Kaeser family names cover many sizes, pressures, controllers and package arrangements. Clear equipment information helps Airtek determine the next useful step and avoids guessing at parts or procedures.
Helpful information for your service request
- Photo of the compressor nameplate
- Full model and serial number
- Controller type and exact message
- Total and load hours, when available
- Observed pressure and temperature
- When the condition started
- Recent maintenance or repair history
- Photos or video of leaks, noise or vibration
- For MOBILAIR units, engine make and engine hours
- Site location, access and production constraints
What operators notice
Kaeser compressor symptoms worth investigating
The same symptom can have several causes. Record the exact controller message and operating conditions, then stop the machine if continued operation could be unsafe or cause further damage.
SIGMA warning or shutdown
A recurring maintenance, temperature, pressure, drive or system message appears on the controller.
High temperature
The package runs hotter than normal, alarms under load or shuts down after operating for a period.
Low or unstable pressure
The compressor does not reach set pressure, pressure falls under demand or control becomes unstable.
Load and unload trouble
The unit will not load, will not unload or cycles more frequently than its previous operating pattern.
Fluid carryover or leaks
Oil appears downstream, fluid level changes unexpectedly or leakage is visible around the package.
SFC or drive fault
A variable-speed unit reports a drive condition, operates at limited speed or behaves differently under changing demand.
Wet air or dryer issue
An integrated T dryer, drain or downstream air-treatment problem affects condensate removal or delivered-air quality.
MOBILAIR operating problem
A portable unit is hard to start, will not build pressure, shuts down under load or shows an engine or compressor warning.
A practical repair path
From service request to working air
The scope is based on the machine, the reported condition and the information available. Airtek keeps the process straightforward and communicates before moving into additional work.
Identify
We confirm the model, serial number, controller, package options, service history and operating complaint.
Diagnose
We inspect the relevant compressor and system conditions, review messages and operating data, and isolate the likely fault area.
Recommend
We explain the findings, required work, known parts requirements and any limits before proceeding beyond the approved scope.
Repair and verify
Approved work is completed and the machine is checked under the operating conditions available at the time of service.
Service questions
Kaeser compressor repair FAQ
These answers cover common intake questions. The exact service path still depends on the machine and the condition reported.
Do you work on both current and older Kaeser compressors?
Airtek can assess current and earlier industrial Kaeser equipment. Serviceability depends on the exact model, serial number, condition, parts access and technical information available for that generation.
What should I send before booking service?
Send a clear nameplate photo, the full model and serial number, controller type, exact message, operating hours and a short description of when the problem occurs. Photos or video of a leak, noise or vibration are also useful.
Can Airtek troubleshoot SIGMA CONTROL messages?
Yes. The exact message and stored operating history can provide useful diagnostic direction. A message identifies a condition, but inspection is still needed before the underlying cause and repair scope can be confirmed.
Do you repair Kaeser MOBILAIR portable compressors?
Airtek can review service requests for industrial MOBILAIR units. Include the compressor model and serial number, engine make, engine hours, controller or warning details, mounting style and the reported operating condition.
Can you check an integrated dryer or condensate problem?
Yes. When a Kaeser package includes a refrigerated dryer or drain, those components can be considered as part of the initial system assessment. The repair scope depends on the installed equipment and the fault found.
Can Airtek source Kaeser compressor parts?
Airtek can investigate parts options using the complete model and serial number. Availability, lead time and suitability must be confirmed for the specific machine before parts are quoted or installed.
Do you offer preventive maintenance?
Yes. Airtek can discuss maintenance based on the equipment, hours, operating environment, existing service history and site needs. A machine-specific plan is more useful than applying one interval to every Kaeser package.
Is the repair completed on site or in the shop?
That depends on the equipment, access, safety requirements and repair scope. Airtek will confirm the practical service location after reviewing the machine details and reported problem.
Keep the air on
Start with the nameplate
Send Airtek the Kaeser model, serial number and exact controller message. We will use those details to determine the right next step for your Edmonton-area service request.
Testimonials
"Their commitment is unmatched, and their sales approach is outstanding ... Their dedication and care truly set them apart, delivering the best service one could ask for."
"Great folks ... they rose to the occasion and got it completed and back in the field. Will gladly recommend to all my industry contacts and colleagues!"
"I have been very happy with my experience dealing with Airtek systems for the past year. They are always very fast to help me with any issues I come across, minimizing downtime and increasing productivity."