Independent industrial compressor service · Edmonton, Alberta
Troubleshooting, maintenance and repair for Quincy rotary screw, reciprocating and oil-free industrial compressor systems—from current packages to established equipment still earning its keep.
Service built around the machine
A Quincy nameplate can identify very different compressor architectures. Airtek starts with the complete model, serial number, controller information and operating complaint, then assesses the compressor and connected air system before recommending work.
What we assess
Quincy industrial equipment
Service scope depends on configuration, age, condition and parts availability. These families cover the industrial Quincy equipment most often identified during intake.
Fixed-speed QSI and variable-speed QGV oil-injected packages used where continuous plant air and high utilization make cooling, separation, controls and drive condition critical.
Fixed- and variable-speed industrial packages. Diagnosis can include load control, temperature events, drive or motor faults, fluid circuits and Airlogic controller alarms.
Smaller packaged systems, including tank-mounted and integrated-dryer configurations. Service can extend from belts and filters to condensate, dryer and control issues.
Long-running single- and two-stage industrial piston equipment. Intake should identify the pump model as well as the complete package, since configuration and age affect parts selection.
Pressure-lubricated QP and splash-lubricated QT packages used for intermittent industrial and shop air, including Pro, Pro+ and Max configurations.
Scroll, tooth, dry-screw and water-injected technologies require model-specific inspection and contamination controls. Contact Airtek first to confirm service capability for the exact package.
Older Quincy equipment: legacy QSI and QR-25 variants, superseded package configurations and earlier controls may still be practical to maintain. A clear nameplate photo lets Airtek verify the exact generation and investigate parts availability before work proceeds.
Faster service intake
Model suffixes, package options and controller generations matter. A few useful details can reduce identification time and help the service team arrive prepared.
Common service calls
These symptoms can have several causes. Proper diagnosis should consider operating conditions and the complete compressed-air system rather than replacing parts from an alarm code alone.
Restricted cooling, fouled coolers, fan or thermostat faults, fluid condition and room ventilation all warrant checks.
Demand, leaks, inlet control, filtration, drive condition, pressure settings and compressor wear can produce similar complaints.
Separator condition, scavenge components, fluid level, temperature, pressure and duty cycle should be assessed together.
Control valves, solenoids, pressure sensing, leaks and controller commands may all affect capacity control.
Alignment, tension, bearings, mounts, couplings, pulleys and internal pump or airend condition may need inspection.
Aftercooling, drains, receiver operation, dryer performance, ambient conditions and filtration should be reviewed as a system.
Supply conditions, current draw, cooling, connections, parameters and mechanical loading can contribute to repeat trips.
Valves, rings, lubrication, unloaders, belts, intercoolers and running speed are common inspection points on reciprocating units.
Alarm history and operating data help separate a failing component from a system or environmental condition.
A practical repair path
Capture the full model, serial number, configuration, controller and operating complaint.
Inspect the unit, review alarms and test the conditions connected to the reported fault.
Review findings, repair scope and parts requirements before authorized work moves ahead.
Run and observe the compressor, confirm the repair and document relevant service findings.
Service FAQ
Airtek evaluates industrial Quincy rotary screw, reciprocating and selected oil-free systems, including QSI, QGV, QGD, QGDV, QGS, QGSV, QR-25, QP and QT families. Exact service scope depends on the model, configuration, condition and parts availability.
Often, yes. Start with the complete model and serial number plus nameplate photos. Older pump variants, package suffixes and control generations can change the correct service information and parts.
Send the model, serial number, operating hours, alarm text, pressure, recent maintenance history and photos of the nameplate and controller. A short description of what changed before the fault is also useful.
Yes. Poor air delivery, pressure loss and wet air can involve receivers, dryers, drains, filters, piping, leaks or plant demand. Airtek can consider these system conditions while diagnosing the compressor complaint.
Airtek can discuss inspection and maintenance based on the equipment, operating hours, environment and service history. Use the service request page to describe the unit and the support you need.
Do not repeatedly reset a unit without understanding the cause. Follow the equipment safety instructions, record the exact alarm and operating conditions, and arrange an assessment—especially for high temperature, low oil pressure, electrical trips, unusual noise or vibration.
"Their commitment is unmatched, and their sales approach is outstanding ... Their dedication and care truly set them apart, delivering the best service one could ask for."
"Great folks ... they rose to the occasion and got it completed and back in the field. Will gladly recommend to all my industry contacts and colleagues!"
"I have been very happy with my experience dealing with Airtek systems for the past year. They are always very fast to help me with any issues I come across, minimizing downtime and increasing productivity."